Miscellaneous Tools Page 1

KTC477
Metal Fabricator's
 Handbook

Over 100,000 copies of this outstanding book have already been sold. It includes sections on basic tool selection and use, MIG, TIG, ARC and GAS welding, fuel and oil tanks, exhaust headers, roll bars and roll cages. Also sheet metal interiors and basic sheet metal fabrication. 175 pages with step by step photos.
$20.00

KTC563
10X Flashlight Magnifier

This is a double lens system with a 3/4" wide flat field of view. The lens diameter is 1-1/16" with a working distance of 3/4". Requires 2 “C” batteries. Not included. $28.00
 

KTC568
Maglite LED Flashlight



 

This is the all new just released, 2D cell Maglite LED flashlight featuring the latest in LED technology. The powerful projecting beam focuses simply by rotating the head. The Interchangeable light source, either a LED module or Krypton bulb (stored in tail cap), is one of the most unique features of the KTC568. Made with an all aluminum anodized body, the switch is protected from moisture by O-rings that are used throughout the body of the flashlight. This is truly a light that will last a lifetime. (Batteries not included).
$34.00

The aircraft timing indicator is a unique device that locates the relative relationship between the crankshaft, magneto point openings, camshaft and valve timing. It easily attaches to the propeller spinner with the supplied mounting bands. The KTC317 quickly and accurately (within 1/2 degree) locates top dead center. It comes with an adjustable dial and an 18 mm hardened aluminum piston stopper.
$69.00
 

KTC478
Sheet Metal Handbook

Inside you will find tips on: setting up your own shop, proper use of the English wheel, basic metal shaping techniques, the art of hammerforming, proper riveting techniques and tips on restoring original sheet metal. 144 pages and step by step photos.  $20.00

KTC318
Differential Cylinder
 Pressure Tester

Quickly locates worn and cracked rings, defective intake and exhaust valves, cylinder and gaskets, or spark plug threads. It is used on all engines with 5.00" or smaller bore. Has a 0.040" orifice and comes with a 18 mm plug adapter. Note: 10mm, 12mm and 14mm adapters are available upon request at additional charge. $86.00

KTC323
Angle Protractor

Measure angle of parts such as wings, flight control, frames, etc. The digital display is accurate to within 0.1 degree and reads in 3 different modes; degrees, % slope and pitch. It can be re-calibrated at the touch of a button and has a built in audible tone alert when the level or plumb is reached. $49.00

KTC479 & KTC480
Motorcycle Metal Fabrication



Watch a master metal fabricator create custom sheet metal parts from scratch, including construction of an aluminum tank, fairings, and front fender in this film. Also featured is step by step fabrication of the bikes entire rear section which includes the fender, sides and seat pan. Each step and every technique is clearly demonstrated in a manner that shows the viewer how to make custom parts of their own design. This 2 piece set is over 3-1/2 hours long.
KTC479 - VHS $59.00
KTC480 - DVD $59.00
 

KTC319
Deluxe Differential Cylinder Pressure Tester



This tester works the same as the KC318 except it comes with a built-in Master Orifice Tester and is highly recommended by TCM per Service Bulletin SBO-3-3
$115.00

KTC360
 Feeler Gauge



Feeler gauges are used for adjusting and gapping spark plugs, distributor paints and valve clearances, etc. Sizes in this 15 blade set include: .002, .003, .004, .005, .006, .007, .008, .010, .012, .013, .014, .015, .020, .025. Metric range is .051 to .635 mm.
$6.00

KTC481 & KTC482
 Basic Technique For
Working In Steel



emonstrates the basic hammer and dollie techniques and shows how to do high-level metal work which requires no filler. Hole filling, patch panels, wired edges, rust repair, metal finishing, and shrinking are all covered in depth. 100 minutes.
KTC481 - VHS $59.00
KTC482 - DVD $59.00

KTC320
High Voltage Cable Tester



The KTC320 high voltage cable tester checks the high voltage aircraft ignition cables quickly and accurately. Simply connect the three wires and push the test button and check the test window. This tool will quickly identify both good and bad cables. It will operate on either 12 or 24 volt DC.
$93.00

KTC656
26 Blade Feeler Gauge


26 blades made of high quality, precision ground heat treated steel to withstand heavy use. Each blade is tested to insure the exact thickness and conveniently stores in the handle for safety when not in use. Each blade is permanently marked for fast and easy size identification for both SAE and metric. The blades are 1/2" wide and 3-5/16" long. Sizes included are: .0015, .002, .0025, .006, .004, .005, .006, .007, .008, .009, .010, .012, .013, .014, .015, .016, .017, .018, .019, .020, .021, .022, .023, .024, .025. Metric sizes from .038mm to .635mm.
$9.00

KTC483 & KTC484
 English Wheel Techniques


Easy to follow using the English wheel, a machine notoriously difficult for beginners to figure out. Demonstrations are given on a broad range of machines, from a cast iron “giant” to a tiny “C”-clamp. Shows basic tracking patterns that are used to shape panels of various sizes and configuration. Also shows the use of a rubber top wheel and embossing with the machine. 90 minutes.
KTC483 - VHS $59.00
KTC484 - DVD $59.00
 

KTC321
Aircraft Magneto
Timing Light

This unit is the industry standard. Designed specifically for the internal timing and synchronization of aircraft magnetos. The KTC321 safely absorbs the current from the magneto impulse coupling - no danger of the engine firing while adjustments are being made. Only 3 wires to connect. $93.00

KTC324
5 Piece Measuring Set


 

Consists of 1 each: 6" divider, 6" inside caliper, 6" outside caliper, 6" pocket ruler inches/metric, 5" vernier caliper. $16.00

KTC485
Shaping Aluminum
With Hand Tools



Every step of making a track roadster nose, demonstrating techniques suitable for making virtually any body panel. Starts with a station buck defining each piece and finally joins them together. Annealing, mallet and sandbag rough shaping, hammer and dolly smoothing and metal finishing are all demonstrated. Oxy-acetylene and TIG welding are also covered in depth. Available in video only. $59.00

KTC321A & KTC321B
Magneto Timing Lights

These lights are perfect for use on all items using a single point magneto. It is often used on automobiles, race cars, outboard motors and motorcycles. Also dual version available for aviation. All solid state, with LED lights, buzzer and 4 foot leads. Packaged in a small 3/4" x 3" x 5" anodized aluminum case.

KTC321A Dual - Aviation $49.00
KTC321B Single $46.00

KTC657
Lead Cutter



 

The Plato shear is the electronic industries most popular lead cutter. The thin profile is designed for those hard to reach areas in electronic assembly. All Plato shears require 50% less operator effort and have an extended cutting life because they shear rather than pinch. The operators love them because of their lightweight, comfort, durability, ease of operation and precision. Flush cuts components leads to 18A WG copper wire, 5.15" OAL, 1.8 oz. $15.00

KTC487
Hammerforming
 Techniques



Two of the best-known names in metal shaping have teamed up to teach you the ins and outs of the hammerforming process. Ten different hammerforming operations are demonstrated with striking close-up shots and clear descriptions of every aspect of the hammerforming process. 76 minutes. DVD Only. $59.00

KTC322
Boroscope


The 18" long, 7/16" diameter flexible fibre optic cable is illuminated by 3 AA batteries. The cable has a “memory” that will retain the position it is bent to. A pressure activated switch assures the light turns off automatically. The sealed lens and cable are submersible, but are not to be used with a flammable liquid or gas.
  $245.00

KTC322-1 45 degree Mirror Attachment
$22.00
KTC322-2 Magnet Attachment $22.00

KTC658 & KTC659
Precision Tweezers


 

These Swiss made precision tweezers are ideally suited for fine electronic assembly and repair work. The fine Swiss quality assures that the points hold their shape even under high use. Made of stainless steel, they are corrosion resistant, anti-magnetic and ESD safe.

KTC658 General Purpose Tweezer
$37.00
KTC659 Curved Tweezer $47.00

KTC489
Metal Shaping & Blocking
& Smoothing Techniques



Techniques of blocking and smoothing aluminum parts using shot bags, mallets, head and slappers. Final smoothing is demonstrated on the English wheel. A variety of shapes are made, including: bowl, tear drop and motorcycle fender. Also, forming a section of a patch panel for a sports car fender using a buck. Thorough explanation of the tools and equipment used to form .050" and .063" aluminum projects. 90 minutes. DVD Only. $34.00

KTC569
Flashlight/Magnetic
Pickup Tool



This is a very handy LED flashlight with a built-in magnet. The light has 6 powerful, 10,000 hour LED’s that illuminate as a standard flashlight as well as functioning as a magnetic retrieval tool. The magnet is retractable from the center of the lens, will extend to 21" OAL and has over 3 pounds of lifting capacity. The flexible shaft at the end allows reaching into confined areas. By using both the light and magnet together, locating and retrieving items becomes easier and faster.
$22.00

KTC325
Rectangular
Telescoping Inspection
Mirror




The inspection mirror is 2-1/8" x 3-1/2" with closed height of 11-1/4" that extends to 15-1/4". The mirror adjusts a full 360° on ball joints that will hold it firmly in place.
$9.00