Miscellaneous Tools Page 2

KTC326
Circular Mirror

The circular inspection mirror is 2-1/4" diameter, 10" collapsed and 14" extended. The double ball joint allows the mirror to swivel 360° for viewing convenience.
$9.00

KTC328
Nut & Bolt Gauge

This combination bolt gauge will quickly and accurately measure nuts, bolts and screws. Measures bolt and nuts from #8 to 1" and metric from #6 to #22. They will measure 7 different sizes of nuts, both course (USS) and fine thread (SAE) from 1/4" to 5/8". Also included is a handy 7" ruler in both inches and mm. The gauge is made of high quality ABS plastic, easy to keep clean and should last a lifetime if given normal care. $8.00

KTC547
 Strut Service Tool

This is a very clean way to service your struts since the strut valve core is not removed. Your hose fitting releases the pressure and fluid into the bottle. Just raise and lower the strut a few
times and then apply the charge.
$28.00

KTC327 
Mirror and Magnet Set

The handle extends from 6-1/2" to 25" and has swivel heads. Set includes a large mirror 2" x 3-1/2", small 1-1/4" mirror, 3 magnets and a storage tray. $29.00

Piston Ring Compressor


Locking pliers and quick change bands help speed up the task of piston ring installation. Available individually or in a complete kit.

KTC664 Locking Piston Ring Pliers $44.00
KTC664-1 3-7/8" - 4-1/8" Band $22.00
KTC664-2 4-1/8" - 4-4/38" Band $26.00
KTC664-3 4-1/2" - 4-3/4" Band $22.00
KTC664-4 4-3/4" - 5" Band $26.00
KTC664-5 5" - 5-1/4" Band $26.00
KTC664-6 5-1/2" - 5-3/4" Band $30.00
KTC664K Complete Kit of Pliers and 6 Bands
$128.00

KTC548
Deluxe Strut
Service Tool

Basically the same as the KTC547 strut service tool except this has 2 large tanks that keep the old and new fluids separate.
$199.00

     
KTC570 & KTC570A
 Spark Plug Cleaner Tester

Manufactured to ISO 9002 standards, this is an ideal unit to quickly clean and accurately test the quality of your used spark plugs. A powerful blast of air and abrasive will knock off the carbon deposits and the plugs are then ready for the “test” side of the tester which will test the plugs at 24,000 volts and up to 150 psi, simulating actual engine conditions. Each Spark Plug Cleaner Tester is shipped with 12mm, 14mm and 18mm spark plug adapters, 12mm, 14mm and 18mm cleaner gaskets, adapter case, aviation massive electrode adapter plug and 1 lb of abrasive. KTC570 operates on 115V phase 50/60 Hz. KTC570A operates on 220V. Recommended air pressure 100 to 140. Dimensions: 19.3" x 11" x 10.4". Weight: 20.5 lbs. 

KTC570 115V Cleaner Tester    $545.00
KTC570A 220V Cleaner Tester $545.00

KTC665
Valve Repair Tool

The four way valve repair tool will repair the outside tire valve thread where the cap is installed, repair the inside valve thread where the core is installed, remove the valve core and remove the valve core body if the core head is broken off. Four handy tools in one.
$3.00

KTC549
 Aircraft Strut Pump

Very portable, no air compressor needed, you can use an air bottle, tire, or tire pump for the air source. (Can also be used with an air compressor if desired). Comes with a 7' hose and instructions. This unit will boost your pressure to 1000 psi. $423.00

 
KTC439
Spark Plug Cleaner

Accepts any size spark plug and has a 2 way valve - 1 position for sand blast and 1 position for clean air. Great tool for aviation, automotive, lawn mower, snowmobile etc.
$23.00

KTC439A Bag - Spare Abrasive (2 lbs.)
$3.00
 

KTC378
High Pressure
Inflator Connector

Max pressure rating of 3000 psig, this connector has a “T” bar that turns to depress the valve care. It fits valves with .305-32 thread (standard) and takes a 1/8" NPT air line connection. $35.00

KTC550
High Pressure
Strut Pump

Provides more than enough pressure to service most aircraft. Built for shop use or the discriminating do-it-yourselfer. It weighs less than 7 lbs and comes equipped with a 36" hose. An adapter is available if you are using bottled nitrogen.
Capable of producing up to 2250 psi air pressure. $546.00

 KTC551 - Nitrogen Adapter Kit $38.00

        
KTC440
Spark Plug
Thread Chaser

Cleans up threads in the cylinder that are cross threaded or stripped. Double ended with 14 mm and 18 mm - works with a standard 13/16" deep socket.
$6.00

       
KTC379
High Pressure
Inflator Connector

This is a “goose neck” style that connects to the air line at a 70° angle. The max rated pressure is 3000 psig, and it fits the standard .305 - 32 thread. This unit depresses the valve core via air pressure. There is no valve core pin depressor in this connector.
$28.00

KTC552
Flat Pivot Point Adjustable Jack Pad

Pivot point adapts to nearly any angle while jacking. It can be used on both tri-gear and tail wheel aircraft. Has width, taper and angle adjustment. Fits Cessna C120, 140, 150, 170, 172, 175, 180, 185, 182, 188, 190, 195, 205, 206, 336, 337, flat gear 177RG, Piper Tomahawk, Beech Skipper, Champion, Bellanca and similar spring steel landing gear. $99.00

KTC660
Magnetic Spark Plug Socket

High quality spark plug socket manufactured from chrome vanadium steel and chrome plated. 6 point, 3/8" square drive and equipped with a magnet to hold the plug securely in place during removal or installation
$45.00

KTC380 & KTC381
 Tire Pressure Gauges

Has a precision made, rugged bronze bourdon tube. 2" face with an un-breathable lens and an easy to read dial. The pressure is indicated and held until a release valve is depressed. Each gauge is tested against master gauges prior to packaging. 
KTC380 - 0 to 60 psi in 1 lb increments - angled, single head chuck $32.00
KTC381 - 0 - 160 psi in 2 lb increments - 12" hose and dual head chuck $55.00
 

KTC553
Round Gear Jack Pad

Cradles round landing gears safely. Fits Cessna C172RG, 177RG, 182RG, 210, T210, P210 and other similar geared aircraft. $88.00

KTC661
Aircraft Spark Plug Socket

A 7/8" hex, extra deep socket, with a 3/8" square drive. This aircraft spark plug socket will handle massive electrode plugs and has a magnet that will firmly hold the plug in place, keeping it from falling out and being damaged.
$35.00
 

KTC502
 Oil Filter Cutter

An economical oil filter cutter that quickly opens the filter for inspection. Works like a typical can opener. Made of 6061 anodized aluminum for durability. Replacement wheels are available. $52.00

KTC503 - Replacement Cutter Wheel
$6.00

KTC554
 C300 Jack Pad

For Cessna 300, 400 and 500 series. Perfect for the Conquest and Citation. $88.00

KTC662 & KTC663
 Spark Plug Gapper

High quality and easy to use, makes this spark plug gapper a great addition to your tool box. It’s designed to easily set the gap on the massive electrode plugs and comes with 2 plug adapters and a wire gapping gauge.
KTC662 Spark Plug Gap Kit $99.00
KTC663 Gap Gauge - $18.00
 

KTC501
Airwolf Oil Filter Cutter

Constructed out of a solid billet of 6061T6 aluminum and finished with a thick layer of black hard coat anodizing to resist scratches and wear. The specially designed, razor sharp cutter wheel, hardened to 60 Rockwell, is easily replaced, but it rarely needs to be. It will last for years of heavy use. The Airwolf Oil Filter Cutter is truly the best there is.  $106.00

KTC555
 RG Jack Pad

For Cessna 182RG with pad mounts.
$88.00