Miscellaneous Tools Page 3

KTC556
 C210 Jack Pad

For Cessna 210 with pad mounts
  $88.00

KTC560
Complete Aero
 Jack System

Service both flat and round gear from one handy kit. $325.00

KTC666
Tire Bead Breaker

Breaks beads easily, with little effort and reduces the risk of damaging expensive cast wheels. It will accept small tail wheels as well as the large tires found on corporate cabin aircraft. Works equally as well on tube or tubeless tires. The Tire Bead Breaker has a 18" x 16" base. $156.00

KTC557
Aircraft Jack

Raise each wheel independently to service brakes or bearings or to change a tire. Use on most near vertical landing gears. Adjustable lifting shelf. This jack has a lift range of 3.5" to 11.5". $211.00

KTC561
Flat Gear Aero Jack Kit

Used for the following aircraft: Cessna C120, 140, 150, 170, 172, 175, 188, 182, 190, 195, 205, 206, 336, 337, flat gear 177RG, Piper Tomahawk, Beech Skipper, Champion, Bellanca and similar landing gears.

$250.00

Tow Bogi-Bars

Light and compact enough to take with you, but strong and durable enough to last a lifetime. These bars are built of high quality, powder coated steel with foam grips on the handles and spreader bar. They are very easy to use, simply push the spreader bar handle forward to open the arms, position the arms over the axel or tow point and release the spreader arms. Now you are ready to tow. For convenience, each bar is extendable to 48" unless noted otherwise. Choose from Tail Wheel or Nose Wheel aircraft.

Tail Wheel Aircraft
Part No.     Description
KTC593-1  Alaskan Bushwheel       
$110.00
KTC593-2 Scott 3200 & 3400          
$110.00
KTC593-3 Cessna XP Modification  
$110.00
KTC593-4 Fairchild 24, Beech Stagger Wing
$110.00
KTC593-5 Vans RV3, RV4, RV6, RV8
$110.00

Part No.    Description
KTC594-1 Beechcraft-Bonanza, Debonair, Duchess, Duke & Skipper (49”)                       
$110.00
KTC594-2 Beechcraft-Musketeer, Sport, Super, Sundowner Sierra & King Air          
  $110.00
KTC594-3 Bellanca-Viking              
$110.00
KTC594-4 Cessna 150, 152, 172, 175, 177 & 182
$110.00
KTC594-5 Cessna 205, 206 & 207    
$110.00
KTC594-6 Cessna 172RG, 177RG, 182RG & 210 series
$135.00
KTC594-7 Cirrus SR20 & 22 series   $110.00
KTC594-8 Gulfstream American AA1 & AA5
$110.00
KTC594-9 Like Amphibian             
$135.00
KTC594-10 Mooney Aircraft        
$110.00
KTC594-11 Piper Comanche PA-24, PA-30 & PA-39 $110.00
KTC594-12 Piper PA28R                
$160.00
KTC594-13 Piper PA-22 & PA-28   
$160.00
KTC594-14 Piper Seneca PA-34-200, PA-34-220, PA-34-220T (extends to 78”)                   
$160.00
KTC594-15 Piper Malibu & Mirage (vehicle pull, extends to 72”)                                 
$195.00
KTC594-16 Socata (extends to 49”)
$110.00
KTC594-17 Vans RV6A, RV7A, RV8A & RV9A
  $110.00
KTC594-18 Vans RV10
$110.00

KTC562
Round Gear Aero Jack Kit

For Cessna C172RG, 177RG, 182RG, 210, T210, P210 and similar landing gears. $250.00

KTC558
 Lil’ Lifter

For use on 800 x 6 tires or smaller. This jack has a lift range of 2.75" to .5", is supplied with 3 pivot heads and only weighs 8.5 lbs.
$173.00

KTC599
 Bungee Tool

Attention Comanche Owners... 30 minutes to change bungees. Safe landings depend on periodically changing the cords. With this tool you have complete control for both the removal and installation. Easy to follow instructions and drawings are included.
$99.00

KTC559
Lil’ Lifter II

Use this on aircraft with 800 x 6 or larger tires. Light weight at only 10 lbs and is supplied with 3 pivoting pads.
$199.00

KTC667
 Battery Charger

 

This 12/24 volt, deep-cycle battery charger is programmable from fully automatic to manual operation. It has a 10 amp charge rate for your everyday charging needs and will fully charge a deep-cycle battery in 7 to 11 hours or an automotive battery in 3 to 5 hours. In the fully automatic mode it will bring a deep-cycle battery to full charge without overcharging the battery. Dimensions: 11-1/8" W x 5-3/8" D x 10-3/8" H. 15 lbs. $199.00

Dimpling Accessories
We carry a wide variety of Rivet Set Adapters, Pressure Pad Assemblies, Punches, Dies & Rams for
Stationary Dimpling machines. Please inquire for items seen below.

Rebuilt Hot Dimpling Machines



(Stationary Style)

Klassic Tool Crib can supply Rebuilt Hot Dimpling machines (Stationary Style) made with the following specifications:
- 24" or 36" Reach
- Safety System & Voltage Protection
- Temperature Range up to 800 degrees
- Capable of 24,000 lbs of force
- Ram Coin or Radius Styles
- Machine comes with 2 Heater assemblies & 1 set of Ram coin punches, dies & rams for 3/32", 1/8", 5/32" and 3/16".
We can also rebuild your existing machinery with our highly trained staff to meet safety standards. So send us your old Chicago Pneumatic, Zephyr & US Industrial machines. $20,000.00

Triple Action Squeezers
  The triple action squeezers have 3 piston cups which enables these tools to build up far more squeezing force than many of the others.  They are available in both a “C” and alligator style with many options available for yokes and jaws. (at additional cost)

"C" Yoke Style
Part No.          Alum      Steel      Reach     Gap      Maxforce      Stroke     OAL      Weight       Price
KAT214TCCC   1/4"          3/16"      1-1/2"     1-1/4"         9,000            9/16"    18-3/4"      8.5 lbs     $1,893.00