KF170PDK-BM
Eckold Bench Model Kraftformer |
 |
The Eckold
KF170PDK-BM Kraftformer is the bench model version of the
KF170PDK. The only difference is that it does not have
the floor stand. It accepts all of the tooling for the
KF170PDK and come with one set of the FWA405K and FWR407K
shrinker and stretcher jaws, plus the foot pedal assembly.
Pre-drilled and tapped holes in the bottom made it easy to
mount on your work bench or you could fabricate a stand to
fit your personal needs. The machine only weighs 205
pounds and requires just 90 psi of air pressure for
operation. (Note table not included) $11,000.00 |
|
Rechargeable LED Worklight |
|
KTC680 |
This 24 element LED
cluster outshines incandescent and fluorescent lights.
Designed to be used in crowded rugged or hard to reach areas
and under extreme temperatures. The 4.8v NiMH
rechargeable battery provides 6 hours of continuous
operation. The included quick charger recharges the
battery in just one hour. It can be hung by the two
rotating hooks and is just 12" long and weighs less than one
pound. $48.00 |
Designed to remove
chips from between sheets after your holes have been
drilled. 10 1/8" OAL with a sturdy molded handle and a
5 7/8" flexible blade. $10.00 |
Pin
Protrusion Gauge
KTC2-1522 |
Manufactured for use
on Hi-Lok™ and Hi-Tigue fasteners, the gauges will determine
if the correct length pin has been installed. This is a
complete set that includes gauges for -5 to -12 fasteners.
$10.00 |
|
Aircraft Tapered
(Pin) Router Bits |
Widely used for
cutting holes in aluminum and plexiglas. The bit has a
cutting edge on the tip allowing you to drill through the
material and then route your hole. The uses are
endless.
|
Part # |
Size |
Shank Dia. |
Flute Length |
OAL |
Price |
|
KTC671A |
#1 |
.098 |
13/16" |
2" |
$5.00 |
|
KTC671B |
#2 |
.1280 |
7/8" |
2-1/4" |
$6.50 |
|
KTC671C |
#3 |
.1875 |
1-1/16" |
2 1/2" |
$8.50 |
|
KTC671D |
#4 |
.2500 |
1-1/4" |
2-3/4" |
$10.00 |
|
KAT214-APS
Bench Top Pedestal
Stand |
The KAT214-APS bench stand is
predrilled to mount on your bench or custom fabricated
stand. It will accommodate CP214, US114 series of
tools, as well as Atlantic and APT. The stand allows
360 degrees of rotation for the tool. Included is a 6
ft. hose and an Air Foot Pedal which allows the operator to
use both hands to hold the parts or for alignment.
(Rivet Squeezer not included). $540.00 |
KAT351-APS
Floor Pedestal Stand |
Our new KAT351-APS air operated,
foot-controlled pedestal stand will accept CP-0351, US151
and APT740 series riveters. It is supplied with a foot
pedal and 8 ft. hose. This stand has a working height of 41"
and will accommodate either a "C" style or "alligator" style
riveter. (Rivet squeezer not included). Shipped
via motor freight item as it weighs 90 lbs. $650.00 |
|
Hollow
Cutter |
 |
Ideal for removing the collar from
Hi-shear fasteners. This high speed steel cutter has 4
flutes and a 1/4" x 28 male threaded shank.
|
Part # |
Size |
OD |
ID |
Price |
|
KTC672A |
1/8" |
.365 |
.124 |
$13.00 |
|
KTC672B |
5/32" |
.365 |
.157 |
$13.00 |
|
KTC672C |
3/16" |
.438 |
.1875 |
$13.00 |
|
KTC672D |
1/4" |
.500 |
.2470 |
$13.00 |
|
KTC672E |
5/16" |
.562 |
.310 |
$13.00 |
|
KTC672F |
3/8" |
.625 |
.373 |
$13.00 |
|
KTC672G |
7/16" |
.750 |
.434 |
$13.00 |
|
|
Short
Shank Rivet Sets |
 |
The short .401 shank on these sets
are designed for use in our KAT-1T rivet gun or others like
it, for riveting in areas with very restricted space.
They are available in straight, offset for AN470 rivets, as
well as flush.
|
Size |
Straight |
Offset |
Flush |
|
3/32" |
SMJ501-4703 -
$10.00 |
SMJ520-4703 -
$12.00 |
SMJ500 -
$10.00 |
| 1/8" |
SMJ510-4704 -
$10.00 |
SMJ520-4704 -
$12.00 |
|
| 5/32" |
SMJ510-4705 -
$10.00 |
SMJ520-4705 -
$12.00 |
|
| 3/16" |
SMJ510-4706 -
$10.00 |
SMJ520-4706 -
$12.00 |
|
|
Jo-Bolt Installation Kit
KTC676K |
 |
A
compact, 13 piece kit that contains everything to install
5/32", 3/16" and 1/4" Jo-Bolts in either flush or protruding
head styles. The package contains a ratchet, grip
gauge and all drivers and socket heads needed. $599.00
|
Jo-Bolt Grip Gauge
KTC676G |
 |
Using this gauge, you can quickly
and accurately determine the correct Jo-Bolt length and
diameter. (Jo-Bolt is also known as Visu-Lok). $13.50
|
Punch and Flange Tool
KTC682 & KTC683 |
360 degree swivel
head will crimp up to 14 gauge steel and will also punch a
clean 3/16" or 5/16" diameter hole for riveting or welding.
Operates on 90 psi air pressure.
|
KTC682 (3/16"
style) $120.00 |
KTC683 (5/16"
Style) $140.00 |
 |
|
|
| Threaded
Drill Collet Adapters |
The 1/4" x 28 threaded drill collet
adapters allow you to use a standard drill bit in your angle
drill or angle drill attachment. Available in #10,
#21, #30, #40 and 1/4". Other sizes available on
request.
| KTCADC-10 $7.00 |
KTCADC-21 $7.00 |
| KTCADC-30 $7.00 |
KTCADC-40 $7.00 |
| KTCADC-1/4 $7.00 |
|
| KTCADCK $30.00
(Includes KTCADC - 10, 21, 30, 40 & 1/4 collet
adapters |
|
| Hi-Lok™
Installation Tool Kit |
|
KTC675K |
 |
Designed
to easily install frangible collar (Hi-Lok™) type fasteners
in the most unusual and awkward situations. The kit
contains 2 roller clutch ratchet heads with a 80 in lb
torque rating, two 1/4" drive studs for use with any 1/4"
drive sockets and a large selection of straight and 90
degree handles that can be assembled in an unlimited number
of configurations. (Also known as the Liberator kit) $129.00 |
|
Hi Lok™
Plier |
|
KTC677 |
 |
Will remove all standard Hi-Lok™
collars while others will not. They are made of
hardened steel with diamond cut jaws for a sure grip and
cushion grip handles. $36.00 |
|
C Frame
Rivet Sets |
|
KTC678 &
KTC679 |
Use these sets to get into those
hard-to-reach areas. One features a 3/16" hole to
accept dimple/dies sets and squeezer sets with .187 shanks
and the other is flat to set flush rivets. Both have a
.401 shank to fit all standard rivet guns.
KTC678 - $30.00
3/16" hole |
KTC679 - $36.00
Flush |
 |
 |
|
High resolution remote color camera
with autofocus. Resolution 320 x 240 pixels. 2-1/2"
full color viewing monitor with waterproof 36" flexible
staylok shaft. Also comes with a mirror and magnet and
high output LED light source. It will operate for 5
hours on 4 AA batteries. $345.00 |
|
Variable Temp Heat Gun Kit |
|
KTC684 |
High
and low temperature settings with soft touch power switch.
Kit comes with 6 LED's indicating temperature range and 80
second automatic cool down function. Temperature range
of 250 degrees F to 1200 degrees F. Kit has 4
specialty attachments and a custom storage case. $80.00
|
|
Electronic Heat Gun |
|
KTC685 |
 |
Compact and lightweight yet
powerful. This heat gun has a variable heat control
range of 250 to 1100 degrees F., 2 speeds and a built in
safety stand. Note 120 volt, 60 HZ and 10 amps. $50.00 |
The piloted paint cutter is used to cut
or score the paint around screw heads before removing the
screw. This will greatly reduce chipping the peeling
paint upon its removal. It has a 1/4" x 28 male thread
and is recommend to be used with a microstop countersink to
control the depth of cut. Available for #4, #6, #8 and
#10 screws or in a kit of all 4 sizes.
|
KTC669-4 - $19.95 |
KTC669-6 $19.95 |
|
KTC669-8 - $19.95 |
KTC669-10 $19.95 |
|
KTC669K
(Kit
Consists of KTC669-4,6,8 & 10)
$65.00 |
|
These specialized sockets are used for
easy removal of aluminum Hi-Lok™ collars. Utilizing a
revolutionary, double start, left hand tapered thread, the
hardened stainless steel socket "bites" into the head of the
Hi-Lok™ collar and "grabs" for easy removal. Its low
profile design accepts using a 1/4" drive ratchet or a
combination wrench. Available in 4 sizes either
individually or as a 4 piece kit.
| KTC687-5/32 $25.00 |
KTC687-3/16 $25.00 |
| KTC687-1/4 $25.00 |
KTC687-5/16 $25.00 |
| KTC687K $93.00
(4 Piece Kit) |
|
This
combination gauge reads in both inch and metric and is used
to measure the "grip-length" of the Hi-Lok™ and Hi-Lite pins,
as well as Cherrylock and Olympic-Lok™ rivets. It is
made of .018 stainless steel and has a slide scale to hold
the reading.
KTC-CATGS1 (scale in metric & inch) $7.00
KTC2-651 (scale with metric and inch readings along with
slide assembly) Shown above - $12.00
|
| 79
LED Rechargeable Worklight |
Features an integrated LED flashlight,
fully detachable mounts behind the worklight. Clear
polycarbonate hinged lens. Light housing constructed
of an unbreakable polymer. 3 position switch, off, 39
LED and 78 LED. Runs up to 4-1/2 hours on full power.
$95.00
|
|
Cobalt Double Margin Jobber Drills |
Designed for close tolerance
drilling in titanium, stainless, heat treated material
and aluminum alloys. The drill point penetrates
enough for the second margin to contact the wall of the
hole. The point is then stabilized and a true
cylindrical geometry is established. Smooth, accurate
holes are produced and reaming can often be eliminated.
135 degree split point provides immediate self-centering
on contact. Meets NAS937 standards.
Other Numbered, letter and
fractional sizes available upon request.
| KTCDMDB-40 #40 $4.00 |
KTCDMDB-30 #30 $4.00 |
| KTCDMDB-27 #27 $4.00 |
KTCDMDB-21 #21 $4.00 |
| KTCDMDB-20 #20 $4.00 |
KTCDMDB-11 #11 $5.00 |
| KTCDMDB-1/4 #1/4 $6.50 |
KTCDMDB-10 #20 $5.00 |
|
|
Hi-Lok™
Installation Tool Assemblies |
The three piece
assemblies consist of a 1/4" sq. dr. ratchet, hex key and a
1/4" sq. dr. socket. used for the more common Hi-Lok™
fasteners.
| |
KTC690-7/32 - $60.00 |
Includes
7/32" Socket, 1/16" hex key and ratchet |
| |
KTC690-7/32 - $60.00 |
Includes
9/32" Socket, 1/16" hex key and ratchet |
| |
KTC690-7/32 - $53.00 |
Includes
5/16" Socket, 1/16" hex key and ratchet |
| |
KTC690-7/32 - $60.00 |
Includes
11/32" Socket, 1/16" hex key and ratchet |
|
|
Hi-Lok
Collar Removal Tool |
These handy and compact "wrenches" are designed to
access tight areas and quickly remove Hi-Lok™
type fasteners without cutting or prying. Has 12
degree offset.
| |
KTC691-5/6
- $84.00 |
For -5 and -6
collars with 5/32" and 3/16" pins dia. 5.6" OAL
handle |
| |
KTC691-8 -
$89.00 |
For -8 collars
with 1/4" pins dia. 6" OAL handle |
| |
KTC691-10 -
$93.00 |
For -10 collars
with 5/16" pins dia. 6" OAL handle |
| |
KTC691-12 -
$94.00 |
For -12
collars with 3/8" pins dia. 7" OAL handle |
| |
KTC691-14 - $98.00 |
For -14 collars
with 7/16" pins dia. 8" OAL handle |
|
|
Hi-Lok™
Hand Reversible Ratchet |
High quality hand ratchet for installation and removal
of Hi-Lok™
type fasteners. They have superior socket retention, a
through hole for the hex key, and a fine tooth ratchet
mechanism for minimal swing and a rugged balanced design for
comfort and durability. Available in 1/4" and 3/8"
square drive and both are reversible.
KTC692-3/8
$41.00 (3/8" Square Drive)
KTC692-1/4 $29.00
(1/4" Square Drive) |
|
|
|
Draw
Cleco Installation Tool |
Used to install or
remove either hex nut or wing nut draw clecos. Use
with any power drill with a 1/4" capacity or larger chuck or
in a power screwdriver with a 1/4" hex chuck.
|
| Hi-Lok™
Box Ratchet Wrench |
Choose either the straight handle or the 25 degree offset
handle style. These are perfect for the easy installation of
Hi-Lok™
type fasteners. Straight style shown above.
|
KTC693A - $36.00 |
1/4" x 9/32"
straight, 4-1/4" long |
|
KTC694A - $40.00 |
1/4" x 9/32"
offset, 4.09" long |
| KTC693A - $36.00 |
5/16" x 11/32
straight, 4/14" long |
|
KTC694B - $37.00 |
5/16" x
11/32" offset, 4.09" long |
| KTC693C - $37.00 |
7/16" x 1/2"
straight, 5-1/2" long |
|
KTC694C - $39.00 |
7/16" x 1/2"
offset, 5.25" long |
|
|
Extended Head Angle Drills |
Available with 45
degree or 90 degree extended angle head, these tools will
allow you to drill in areas previously inaccessible.
They have a 1/4" drilling capacity and operate at 3,000 rpm.
Both tools have a 1/4" x 28 internally threaded spindle.
|
KAT113-EXT $295.00 |
90 degree
head, 13-3/8" OAL, 2.0 lbs |
|
KAT114-EXT $315.00 |
45 degree
head, 14-7/8" OAL, 2.1 lbs |
|
